Resistor Resistor RIP Category="Electrical components"

[image]
[image] [image]
Resistor Variable
Resistor

Resistor symbols

A resistor is a two-terminal electrical or electronic component that resists the flow of current, producing a voltage drop between its terminals in accordance with Ohm's law. The Electrical resistance is equal to the voltage drop across the resistor divided by the current that is flowing through the resistor. Resistors are used as part of electrical networks and electronic circuits.

Applications

In general, a resistor is used to create a known voltage-to-current ratio in an electric circuit. If the current in a circuit is known, then a resistor can be used to create a known potential difference proportional to that current. Conversely, if the potential difference between two points in a circuit is known, a resistor can be used to create a known current proportional to that difference.
An attenuator is a network of two or more resistors (a Voltage divider) used to reduce the voltage of a signal.
A line terminator is a resistor at the end of a Transmission line or Daisy chain Bus (such as in SCSI), designed to match impedance and hence minimize reflections of the signal.

The ideal resistor

The SI unit of electrical resistance is the Ohm. A component has a resistance of 1 ohm if a voltage of 1 Volt across the component results in a current of 1 Ampere, or amp, which is equivalent to a flow of one Coulomb of electrical charge (approximately 6.241506 × 10¹⁸ electrons) per Second.

In an ideal resistor, the resistance remains constant regardless of the applied voltage or current flowing through the device or the rate of change of the current. While real resistors cannot attain this goal, they are designed to present little variation in electrical resistance when subjected to these changes, or to changing Temperature and other environmental factors.

Non-ideal characteristics

A resistor has a maximum working voltage and current above which the resistance may change (drastically, in some cases) or the resistor may be physically damaged (burn up, for instance). Although some resistors have specified voltage and current ratings, most are rated with a maximum power which is determined by the physical size. Common power ratings for carbon composition and metal-film resistors are 1/8 Watt, 1/4 watt, and 1/2 watt. Metal-film resistors are more stable than carbon resistors against temperature changes and age. Larger resistors are able to dissipate more heat because of their larger surface area. Wire-wound and sand-filled resistors are used when a high power rating is required.

Furthermore, all real resistors also introduce some Inductance and a small amount of capacitance, which change the dynamic behavior of the resistor from the ideal.

Types of resistor

[image] Resistors may be fixed or variable.

Fixed resistors

Some resistors are cylindrical, with the actual resistive material in the centre (composition resistors) or on the surface of the cylinder film resistors, and a conducting metal lead projecting along the axis of the cylinder at each end. This is called an axial package resistor. The photo above right shows a row of common resistors. Power resistors come in larger packages designed to dissipate heat efficiently. At high power levels, resistors tend to be wire wound types. Resistors used in computers and other devices are typically much smaller, often in surface-mount packages without wire leads. Resistors are built into integrated circuits as part of the fabrication process. A single IC may contain millions of resistors..

Variable resistors

The variable resistor is a resistor whose value can be adjusted by turning a shaft or sliding a control. These are also called potentiometers or rheostats and allow the resistance of the device to be altered by hand. Variable resistors can be inexpensive single-turn types or multi-turn types with a helical element. Some variable resistors can be fitted with a mechanical display to count the turns. [image] Variable resistors can sometimes be unreliable, because the wire or metal can corrode or wear. Some modern variable resistors use plastic materials that do not corrode and have better wear characteristics.

Some examples include:

a rheostat: a variable resistor with two terminals, one fixed and one sliding. It is often used with high currents.
a Potentiometer: a common type of variable resistor. One common use is as volume controls on audio amplifiers and other forms of amplifier.

Other types of resistor

Note that some of the following resistors do not obey Ohms law

A metal oxide Varistor (MOV) is a special type of resistor that has two very different resistance values: a very high resistance at low voltage (below the trigger voltage) and very low resistance at high voltage (above the trigger voltage). It is usually used for short circuit protection in power strips or lightning bolt "arrestors" on street power poles, or as a "snubber" in inductive circuits.
A Thermistor is a temperature-dependent resistor. There are two kinds, classified according to the sign of their temperature coefficients:
- A Positive Temperature Coefficient (PTC) resistor is a resistor with a positive temperature coefficient. When the temperature rises the resistance of the PTC increases. PTCs are often found in televisions in series with the demagnetizing coil where they are used to provide a short-duration current burst through the coil when the TV is turned on. One specialized version of a PTC is the Polyswitch which acts as a self-repairing fuse.
- A Negative Temperature Coefficient (NTC) resistor is also a temperature-dependent resistor, but with a negative temperature coefficient. When the temperature rises the resistance of the NTC drops. NTCs are often used in simple temperature detectors and measuring instruments.
A sensistor is a semicondutor-based resistor with a negative temperature coefficient, useful in compensating for temperature-induced effects in electronic circuits.
Light-sensitive resistors are discussed in the Photoresistor article.
All wire, except for superconductors, exhibits some resistance, based on its cross section area and the conductivity of the material it is made of.

Identifying resistors

Most axial resistors use a pattern of coloured stripes to indicate resistance. SMT ones follow a numerical pattern. Cases are usually brown, blue, or green, though other colours are occasionally found like dark red or dark gray.

4-band axial resistors

: Main article: Electronic color code

4 band identification is the most commonly used colour coding scheme on all resistors. It consists of four coloured bands that are painted around the body of the resistor. The scheme is simple: The first two numbers are the first two significant digits of the resistance value, the third is a multiplier, and the fourth is the tolerance of the value. Each colour corresponds to a certain number, shown in the chart below. The tolerance for a 4-band resistor will be 2%, 5%, or 10%.

The Standard EIA Color Code Table per EIA-RS-279 is as follows:

Colour\ 1^st band\ 2^nd band\ 3^rd band (multiplier)\ 4^th band (tolerance)\ Temp. Coefficient
Black 0 0 ×10⁰
Brown 1 1 ×10¹ ą1% (F) 100 ppm
Red 2 2 ×10² ą2% (G) 50 ppm
Orange 3 3 ×10³ 15 ppm
Yellow 4 4 ×10⁴ 25 ppm
Green 5 5 ×10⁵ ą0.5% (D)
Blue 6 6 ×10⁶ ą0.25% (C)
Violet 7 7 ×10⁷ ą0.1% (B)
Gray 8 8 ×10⁸ ą0.05% (A)
White 9 9 ×10⁹
Gold ×0.1 ą5% (J)
Silver ×0.01 ą10% (K)
None ą20% (M)

Colour\	1^st band\	2^nd band\	3^rd band (multiplier)\	4^th band (tolerance)\	Temp. Coefficient
Black	0	0	×10⁰
Brown	1	1	×10¹	ą1% (F)	100 ppm
Red	2	2	×10²	ą2% (G)	50 ppm
Orange	3	3	×10³		15 ppm
Yellow	4	4	×10⁴		25 ppm
Green	5	5	×10⁵	ą0.5% (D)
Blue	6	6	×10⁶	ą0.25% (C)
Violet	7	7	×10⁷	ą0.1% (B)
Gray	8	8	×10⁸	ą0.05% (A)
White	9	9	×10⁹
Gold			×0.1	ą5% (J)
Silver			×0.01	ą10% (K)
None				ą20% (M)

Note: red to violet are the colours of the rainbow where red is low energy and violet is higher energy.

Resistors use specific values, which are determined by their tolerance. These values repeat for every exponent; 6.8, 68, 680, etc. This is useful because the digits, and hence the first two or three stripes, will always be similar patterns of colours, which make them easier to recognize.

Preferred values

Standard resistors are manufactured in values from a few milliohms to about a gigohm; only a limited range of values called preferred values are available. In practice, the discrete component sold as a "resistor" is not a perfect resistance, as defined above. Resistors are often marked with their tolerance (maximum expected variation from the marked resistance). On color coded resistors the color of the rightmost band denotes the tolerance:

: silver 10%
: gold 5%
: red 2%
: brown 1%.

Closer tolerance resistors, called precision resistors, are also available.

5-band axial resistors

5-band identification is used for higher tolerance resistors (1%, 0.5%, 0.25%, 0.1%), to notate the extra digit. The first three bands represent the significant digits, the fourth is the multiplier, and the fifth is the tolerance. 5-band standard tolerance resistors are sometimes encountered, generally on older or specialized resistors. They can be identified by noting a standard tolerance color in the 4th band. The 5th band in this case is the temperature coefficient.

SMT resistors

Surface-mount resistors are printed with numerical values in a code related to that used on axial resistors. Standard-tolerance SMT resistors are marked with a three-digit code, in which the first two digits are the first two significant digits of the value and the third digit is the power of ten. For example, "472" represents "47" (the first two digits) multiplied by ten to the power "2" (the third digit), i.e. 47 × 10² = 47 × 100 = 4700 { ohms} . Precision SMT resistors are marked with a four-digit code in which the first three digits are the first three significant digits of the value and the fourth digit is the power of ten.

Industrial type designation

In industrial type designation, the first two digits represent the significant figures and the third gives the number of zeros to folow.
For resistance value less than 10 Ω, the letter (G) substituted in place of the third digit signifies a Decimal Multiplier of 0.1

e.g.: 27G represents a resistance of 2.7 Ω.

Another digit following the resistance value code gives the percentage tolerance.
Digits used to represent the tolerances of ±5%, ±10% and ±20% are 5, 1 and 2 respectively.
The power rating is expressed by two letters preceding the resistance value code. These letters are BB, CB, EB, GB, HB, GM and HM respectively for
{ 1
––
8 } , { 1
––
4 } , { 1
––
2 }
, 1, 2, 3 and 4 W resistors.

♠ The operational Temperature range distinguishes Commercial grade components from the industrial grade components. Commercial grade: 0^∘ C to 70^∘ C Industrial grade: -25^∘ C to +85^∘ C

Calculations

Ohm's law

The relationship between voltage, current, and resistance through an object is given by a simple equation which is called Ohm's Law:

: V = I • R

where V is the voltage across the object in volts (in Europe, U), I is the current through the object in amperes, and R is the resistance in ohms. (In fact this is only a simplification of the original Ohm's law - see the article on that law for further details.) If V and I have a linear relationship -- that is, R is constant -- along a range of values, the material of the object is said to be ohmic over that range. An ideal resistor has a fixed resistance across all frequencies and amplitudes of voltage or current.

Superconducting materials at very low temperatures have zero resistance. Insulators (such as Air, Diamond, or other non-conducting materials) may have extremely high (but not infinite) resistance, but break down and admit a larger flow of current under sufficiently high voltage.

Power dissipation

The power dissipated by a resistor is the voltage across the resistor times the current through the resistor:

P = I • V = I² R =

V²
–––
R

All three equations are equivalent, the last two being derived from the first by Ohm's Law.

The total amount of heat energy released per unit time is the integral of the power:

nW = ∫

t₂

t₁

v (t) i (t) dt n

If the average power dissipated exceeds the Power rating of the resistor, then the resistor will first depart from its nominal resistance, and will then be destroyed by overheating.

Series and parallel circuits

Resistors in a parallel configuration each have the same potential difference (voltage). To find their total equivalent resistance (R_eq):

: [image]

1
–––––
R_eq

1
–––
R₁

1
–––
R₂

+ … +

1
–––
R_n

The parallel property can be represented in equations by two vertical lines "